Opus has 41 settings on the outer adjustment ring, which can be seen when looking directly at Opus. This ring can adjust between numbered settings from 1 to 11. Between each numbered setting are 4 minor increments, allowing you to set your grind setting by increments of 0.25. With this setup, there are technically 120 positions on Opus.

Underneath the load bin is a blue ring that allows you to get between the 4 minor increments in the outer ring. That’s what we mean by “41

Opus has two grind adjustment rings: an outer ring and an inner ring. Use these rings to set your optimal grind size.

The outer ring

The outer ring can be seen when looking directly at Opus. This ring can adjust between numbered settings from 1 to 11. On this outer ring, 1 is the finest setting and 11 is the coarsest. Between each numbered setting are 4 minor increments, allowing you to set your grind setting by increments of 0.25.

The inner ring

Inside Opus, there is a second inner adjustment ring. You can access the inner ring by removing the load bin. Use the inner ring to:

Enable micro adjustments on the outer ring. By adjusting the inner ring by one notch, you shift the range of the outer ring by 2/3 (.667) of a notch. Because the outer ring is measured by increments of 1/4 (0.25), utilizing the inner ring enables Opus to get between those increments by 1/6 of a measure.

If you really want to geek out: One outer ring adjustment is equivalent to 50 microns of burr height movement. With the inner ring design, you can split those outer adjustments into 3rds, allowing for 16.7 microns of burr adjustment throughout the range.

To expand the grind range on Opus. By adjusting the inner ring all the way to the one end or the other, you enable the outer ring to reach setting “0” (1 full setting finer than 1) and “12” (1 full setting coarser than 11). This is because there are a maximum of 6 notches on the inner ring, and 6 inner notches is equivalent to 1 full outer setting.

To calibrate Opus as the burrs wear down. With prolonged use, the burrs may start to output coarser grinds. To adjust for this, you can slowly shift the inner ring to a finer setting. Though the burrs are built to last for the lifetime of the product, burr wear is natural.

How to adjust the inner ring:

1. Ensure the load bin is empty.

2. Rotate the outer ring until it is centered at setting 6.

3. Remove the load bin by twisting it counterclockwise until it unlocks from the grinder, then lift away. The blue inner ring should now be visible.

4. With your thumb and index finger, press down with even pressure on the two exposed tabs of the calibration ring to compress the spring-loaded mechanism. Keep pressing until you feel the ring bottom out.

5. With the inner blue ring pressed down, use your other hand to rotate the outer ring in either direction, which will change where the arrow is pointing on the inner ring scale (counterclockwise towards the “-” is finer, clockwise towards the “+” is coarser).

6. Each notch on the inner ring is equivalent to 2/3 of a minor increment on the outer ring. Each minor increment is 0.25, so each inner ring notch is equivalent to ⅔ * ¼ = ⅙ of a numbered setting. There are a total of 6 notches on the inner ring in either direction.

7. When you’ve reached the desired setting, release the calibration ring so it springs back up and engages with the grind adjustment ring. Rotate the grind adjustment ring to ensure the calibration ring rotates with it again.

8. Finally, reinstall the load bin. Please make sure the load bin is fully seated and the Opus turns on. If the Opus does not turn on, you may need to readjust the load bin. This is a safety feature to ensure everything is locked into place.

Exterior: We recommend using a non-abrasive damp cloth to wipe down the exterior and load bin of Opus.

Exit Chute/Anti Static: The anti static technology will work best for about 60 cycles before it needs to be cleaned to operate at its peak performance. To clean it, remove the catch cup, and use the Fellow cleaning brush (or another cleaning brush such as a clean makeup brush or a clean paint brush) and “swipe” around the inside of the exit chute (where the coffee grounds come out). This will clean the chute and help the anti-static mechanisms work well.

Burrs:Take the load bin off, remove the outer burr, and brush the burrs with the Fellow cleaning brush (or another cleaning brush such as a clean makeup brush or a clean paint brush).

Yes! Opus can grind for all brew methods, from the finest espresso for a true 9-bar shot all the way to the coarsest coffee for cold brew.

1. Don’t store beans in Opus. Pour beans into the load bin right before grinding. The fresher the coffee, the better the flavor.

2. Dial in your espresso by using the inner ring to make granular grind adjustments.

3. If your brew tastes sour, go a few clicks finer.
If your brew tastes bitter, try using a coarser grind.

4. Time your grind! Just press the power button for different timed grinds:
• Single short press for 30 seconds
• Double short press for 60 seconds
• Triple short press for 90 seconds
• Press and hold for 1 second to grind for 2 minutes
To stop Opus before the timer expires, simply press the power button during operation. Otherwise, Opus will stop automatically.